Auto Repair in Camarillo

Some problems are easy to diagnose on a vehicle; others aren't.  Figuring out what's wrong with a malfunctioning turn signal sometimes fits into both categories.  By the way, if your tempted to just leave your broken blinker broken, remember you can get a ticket for not using them, not to mention you are missing a great chance to communicate your intentions to other drivers on the road.

There can be lots of signals that your signals are on the blink.  Does only the driver's side signal not work or the passenger's side? Do your hazard signals work? Do the lights illuminate but not flash? Can you see the indicators on the dash blinking? Do your turn signals turn off after you've finished your turn or do they stay on?  These are all great clues for the technician.

Here's one common symptom to take note of.  Your signal all of a sudden starts blinking much more quickly than it used to.  It could be a simple as a burned out bulb.  But there are many different parts that go into the turn signal system.  There are fuses that blow, switches that can fail, flasher modules that go bad and light bulb sockets that can simply get corroded or dirty.  When that happens, it's possible there's no contact between the bulb and the socket.

So it's understandable how tracking down the source of the problem can involve some detective work.  Your service facility has equipment that can nail down the cause of your problems. They may also consult the repair manual.  One thing to be aware of: if your vehicle has airbags, they may have to be disabled so they don't accidentally go off.

You can make sure your turn signals are working correctly by having them checked by a trained technician.  Other drivers will thank you for showing them the courtesy of signaling your intentions.  It's a courteous and considerate thing to do, not to mention it makes the road a safer place. 

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

When you feel your vehicle vibrating as you're driving down the road, one cause could be something you may not have ever seen: your driveshaft.  It is underneath the vehicle and most drivers don't climb under there to take a look very often.  The driveshaft is a cylindrical part that helps conduct the rotational power from your engine to your drive wheels.  If you have a four-wheel drive vehicle, you may have two driveshafts. 

The drive shaft has bushings, and when they wear out, that's a likely source of the vibrations.  When the bushings are in good condition, they prevent the driveshaft from vibrating.  And if you don't get your vehicle repaired fairly soon after discovering vibrations, they'll continue to get worse and cause other components of the drivetrain to wear out.

The driveshaft is, of course, only one part of the drivetrain.  It includes other parts such as axles, transmission, differentials and joints.  They all work together and need to be maintained properly.  When a driveshaft fails, there can be symptoms other than vibrations.  They include difficulty turning, rattles, clunks and squeaks coming from underneath your vehicle. You may even feel a shudder when you accelerate from a stop.

Driveshafts can fail when they get corroded or damaged by rough roads, curbs and debris. A trained technician with experience working on drivetrains uses specialized equipment that doesn't further damage the drivetrain's other parts.  Sometimes the entire driveshaft will have to be replaced; sometimes the problems can be fixed by replacing individual components. 

Your vehicle's drivetrain was engineered to propel you smoothly down the road.  When time and distance begin to take their toll, have your vehicle looked at by your service facility. They'll know how to properly pinpoint what's causing your problems and restore your vehicle to the reliable, smooth, safe machine its designers worked hard to create.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

If you've ever gotten in an unfamiliar vehicle, maybe a rental car, you may have pulled up to the gas pump and wondered, "Which side is the fuel filler on?" Here's a tip for you.  There is usually a little arrow on the instrument panel near the fuel gauge that points to the side where the fuel filler is. 

But why are the fuel fillers not all on the same side, anyway? There are lots of reasons.  At one time, many manufacturers tried putting them in an easy-to-reach spot: in the center of the vehicle's rear end.  Some even hid them behind a hinged license plate door.  Cool place, but it turned out not to be a good idea.  When a vehicle with a fuel filler in the rear was hit by another vehicle from behind, it was much more prone to catch fire and explode.

Safety regulations now dictate that the fuel filler doors be placed within crumple zones and away from where they can drip fuel on hot exhaust pipes or near electrical connections.  But why do manufacturers put them on either side?

Some say it should be on the side away from the road.  That way if you run out of gas and have to add a little from a gas can as your standing at the side of the road, you'll be a little farther away from passing traffic.  So some companies from North America and many European firms with left-hand drive put their fillers on the right side.

Some manufacturers think convenience for the driver is paramount, so they put their fuel fillers on the driver's side.  If you have a vehicle with a cable release for the fuel door inside the cabin, it's usually on the same side as the steering wheel.  As you can see, there's no standardization.

Fuel doors need regular maintenance such as lubrication, and your gas cap (if your vehicle has one) should seal properly.  Have your service facility inspect those regularly. Wherever your fuel filler is, it's obviously important that you can get at it easily because you have to fuel up sometime. Otherwise, you're not going to go too far!

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

Your vehicle's engine makes a lot of heat when it's powering you down the road, so it needs a way to get rid of that energy.  That's why your vehicle has a cooling system, complete with a radiator and one or two radiator fans, also called cooling fans.  Those fans make sure air keeps moving across the radiator so that the heat stored in the coolant can be dissipated outside when the vehicle is stopped or not traveling fast.

Radiator fans can develop problems and can stop working properly or stop working altogether.  Some signs to look for? If you're driving slowly and idling and you see your temperature gauge moving toward the red or hot zone, that could spell trouble.  Another thing you may notice when a radiator fan is failing is that there may be a loud noise coming from the engine compartment.

There are two types of radiator fans.  One is mechanically connected to the engine and uses the engine's rotational energy to turn it.  The other is an electric fan and is the type used in most newer vehicles.  In the electrical type, one of the components, such as a relay or fuse, may fail, causing the fan to stop turning.  In the mechanical type, since it's driven by a pulley/belt mechanism, one of those components may break or stop working properly.  A clutch can wear out or a belt may slip or break. 

When your cooling fan isn't working properly, it may cause your engine to overheat which could lead to expensive damage. That's why it's important to make sure you visit your service facility if you notice any of these symptoms.  A technician is trained to diagnose the problem and make sure your radiator fan is doing its job.  When it comes to your vehicle, your radiator fan really is your biggest fan.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

So your vehicle won't start.  What's the first thing that comes to mind?  Battery dead? Starter motor worn out? Out of gas?  Well, those are all reasons that make sense.  But your vehicle may be refusing to start because one of its computers is being warned that to do so might damage it.  Here's how that works.

You have lots of computers in your vehicle.  They need to know the status of things so there are several sensors monitoring various things going on.  These sensors send information to the computers that adjust the fuel and air mixture so you don't waste fuel.  They know when things aren't quite right and prevent you from starting your engine if that's going to damage it. 

Other sensors make sure the coolant is the right temperature, check to see you are not polluting the air and make sure other electronic components are performing their tasks correctly.

Here's an example of a sensor doing its job.  Your engine needs oil to lubricate metal components so the friction doesn't damage them.  Your engine has an oil pressure sensor that tells a computer called the Electronic Control Unit (ECU) if things are good to go or if there's something wrong, maybe the oil pressure is too low to keep things lubricated.  If it is, it gives a signal for the vehicle not to start, protecting the engine. 

Of course, the sensors can go bad, too, with some of the same results.  And so someone has to figure out if it's the sensor that's failed or if it really has detected a problem.  That is the challenge for technicians with specialized equipment to decipher the signs.  If a bad sensor is found, it may need to be replaced.  Sometimes a thorough cleaning can do the trick.  In either case, your service facility can track down the problem and get you back on the road.  Makes sense, doesn't it?

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

Would you buy a jacket without even trying it on? Probably not, but it might surprise you that one study shows about half the people buy a vehicle after a short test drive around the block or none at all.  If you're in the market for another vehicle, make sure you check out the most important things so you'll know if that's the right vehicle for you.

Check out the gadgets.  Love a good sound system? Then turn it up loud.  Does it have enough bass for you? See how you like its navigation system if it has one.  Try pairing your Bluetooth smartphone with the vehicle.  Test out how to set the cruise control and how steady it keeps the speed. Back up and check out the rearview camera. If you buy this vehicle, you'll have to live with all of these things every time you drive.

Test the vehicle on roads you know.  See how it handles bumps and potholes, how it takes that tight curve that you drive every day to and from work.  Driving on familiar roads gives you a chance to compare what you know with what you're thinking about buying.

Check the fit.  One suburban driver drove a full-sized SUV and loved it until they got it home and realized it was too high for her old garage.  Remodeling the garage would be the only answer! Try installing your child seats.  Size matters, especially in a vehicle.

Gauge the fuel economy. Many vehicles have a trip computer that will calculate fuel economy quickly.  Here's a tip: you can reset it before your test drive and when you're finished, check it and see what fuel economy you got.  It will be a smaller sampling than would be ideal, but it will give you an idea.

Take as much time as you can.  A lot of sellers will pressure you to restrict your test drive to 10-15 minutes.  Ideally, you'd like to have that vehicle for a week, but that's usually not possible. So try for something in between. Remember, this could be your vehicle for years to come.

Keep in mind that every vehicle will feel strange to you at first. Buying a vehicle is a little like getting married.  You want that marriage to be happy, and you want it to last, so take the time to get to know it as well as you can.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

What a convenience power door locks are on a vehicle.  The latest don't even require you to push the button on the key fob; all you have to do is have it with you.  But sometimes there's a component of power door locks that can fail, especially when they are used several times each day.  Those are called the door lock actuators.

The actuator is an electric part that works with others (like motors and gears) to lock and unlock doors.  You can hear them work, sometimes with the little whirr of the gear or the quiet clunk of the lock finishing its cycle.  And it's good to pay attention to that sound because if it starts to sound different, it could be a signal that your lock is on the brink of failing. Another sign of a failing power door lock actuator is they start working intermittently or quickly and erratically.  The driver's door is often the first to start acting up since it's the one that usually gets the most use.

When you start to notice these signs, consider a visit to your service facility to get your vehicle checked out.  If you wait too long, you may find yourself getting locked out of your vehicle. Many vehicles do have mechanical keys available as a failsafe so you are at least able to get inside.  Some of them are hidden inside the key fob and you should know how to access them.  Check with your owner's manual or ask your service advisor.

It's extremely inconvenient to have to unlock your vehicle with the mechanical key, then get inside and unlock the other doors. It's even more inconvenient if you have passengers in the rear seats.  And that doesn't even count having to go through the same thing to lock the doors when you arrive at your destination.

There are many things that can cause power door locks to malfunction, but if it turns out to be a power lock actuator, the most common remedy is to replace it.  Some are easier for technicians to reach than others, depending on your vehicle's design.  But once your locks are working again, you might think you've found the "key" to happiness!

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

Alfred Hitchcock once made a mystery thriller film called "Rear Window." It had nothing to do with the rear window of today's cars, SUVs, CUVs and light trucks.  But there is one thing that some drivers DO find mysterious.  Why don't the rear windows in the second row of many of these vehicles go down all the way?

You've probably seen or owned one or two. That rear side window only goes down about a third, a half or three-quarters of the way. Yet there are some similar vehicles where the window goes down all the way.  What gives?

There was the rumor going around that the restriction on how far those windows could go down was a child safety feature.  The thought was that if those windows couldn't open up fully, a child (or pet) would be less likely to fall out.  But it turns out the real reason is that the way the rear doors were designed, there was just no room for the window to go down all the way into.

Many vehicles are configured so that the rear wheel arch continues into the rear door.  That arch restricts the space that would accommodate the window, so they had to stop the window somewhere higher than bottom of the door.

Seems buyers would prefer those back windows to go all the way down, so many manufacturers are changing designs to make that happen.  Longer vehicles can have their wheels pushed further back so the wheel arch isn't an issue.  Some have altered the position of the rear window track. 

If you have any questions about your rear side windows, you may want to consult your service advisor to check yours.  If they ARE supposed to go all the way down and they're not, it could be due to a few problems: corrosion, broken or bent window regulator components, electrical issues, etc. But if they're not supposed to go down all the way?  At least now you know for sure.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

Most would agree they'd rather drive around in a clean, shiny vehicle than one coated with a layer of dirt.  When warmer weather comes around, some of us are bound and determined to wash our own vehicles.  And to protect the paint and its luster, there are a few things to keep in mind when you get out the bucket and soap.

• Cool body.  It's not a good idea to wash a vehicle when the body is hot.  If it's been sitting out in the sun or you've been riding around on a sunny day, make sure you cool your vehicle off by either moving it to the shade or wetting it down with cool water. The problem with washing a hot vehicle is that it's going to dry so fast, minerals in the water can form hard-to-remove spots on the paint.  And some of those can be really difficult to get out.  Best to avoid it.
• Slippery when wet.  Make sure you wet your vehicle down thoroughly before you get the washing mitt out.  Experts keep a couple of buckets of soapy water on hand, and they use soap especially engineered to remove dirt from a vehicle without stripping off the wax that might be on it. 
• The washing mitt.  Experts say to use a mitt with hundreds of moisture-absorbing strands on it.  Start washing at the top and move down.  If you keep dipping the mitt in the buckets frequently, a minimal amount of dirt will stick to it and that will prevent scratching the paint. 
• Wheels last.  Wait until you've finished washing the body before washing the wheels.  Some detailers prefer special wheel-washing tools or brushes. 
• Rinse it well.  Hose the vehicle off thoroughly to get all the soap off, then dry immediately.  Some people swear by a chamois, others like cloth better.  Cotton or microfiber towels will do.  

The next time you have your vehicle in for maintenance, you might ask your service advisor for recommendations on vehicle washing accessories.  They are usually up on the brands that produce the best results.  You may not be a detailing pro, but there's no reason your vehicle can't look like you are.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

In the hot weather, seeing steam coming from the engine compartment is something we all dread.  No one wants that to happen to them. But if you know the signs of overheating and how to deal with it, you may be able to reduce the risk of damage to your vehicle, maybe even prevent getting stranded on the road.

Besides the steam coming out of the engine compartment, here are a few signs of overheating.  Your vehicle has a heat gauge that may have a needle that can go into a red zone or up to the "H" (for High) position.  You may smell odors, perhaps a burning (could be hot oil) or a sweet smell (engine coolant leaking). 

When you encounter any of those signs, you know you have to do something to keep the engine as cool as possible to avoid potentially catastrophic damage.  Turn off the air conditioning and turn up the heat.  While that last part may sound odd, it helps draw heat out of the engine. 

If you can do it safely, pull off the road to a spot away from traffic.  Turn off the engine so it can cool down for a few minutes.  You may want to call for help at this point, then switch on the key to "accessory" position to see if the engine has cooled down to the normal range.  You may have to have your car towed to a service facility or, if there's one nearby, you may be able to slowly drive to it.  But keep your eye on the heat gauge and immediately stop if it starts to overheat again. 

The best hedge against engine overheating is regular maintenance.  When the cooling system and other engine components are working like they should, your chances of an overheated engine are drastically reduced.  Your service facility will keep their eyes open for leaking hoses, cracked belts, rusted pipes and other things so they don't fail at the most inopportune time.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com