Auto Repair in Camarillo

Welcome to the world of infrequently-used parking brakes.  Yes, they do stick for several reasons. It's common for components to corrode and get locked up.  Sometimes if you have applied it extra hard, it can jam.  Could be a rusty cable, or it could be a spring that doesn't return the brake to its disengaged position.  Some pieces just break when they're stressed for the first time in a while. A caliper or the pivot arm it's on can also stick.

There are a few things you can try to unstick it.  Carefully rock your vehicle by putting it first in drive and then reverse.  You have to be careful doing that, though, because sometimes you can damage the transmission.  You can try working the parking brake control a few times to see if that will loosen the corrosion.  If you can't unstick it, you can try driving slowly a short distance to a repair facility near you.  Sometimes it won't cause damage to the brakes, but it depends on how tightly the parking brake was applied and what was stuck.  You may also have to have your vehicle towed to a repair facility.

In any case, once you've seen these symptoms, have your vehicle's brakes looked at by a professional who can fix the root of the problem.  Better yet, don't let your vehicle get in this condition; regular maintenance and inspections by a trained technician should prevent you from getting in a jam somewhere thanks to a stuck parking brake.  You could use a "brake" like that.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

Of the things you think about most, your tires are probably pretty far down the list. That’s understandable because today’s tires are engineered to do their job without needing you to pay too much attention to them. But they DO wear out, and worn tires can contribute to skidding in bad weather, not being able to stop, a ride full of uncomfortable vibrations and, even a sudden blowout. Yikes. Let’s figure out right now how to know if your tires need replacing!

Let’s face it. Most of us don’t know the first thing about tires. So, the best way to make sure what shape yours are in is to take your vehicle to a qualified service facility to have the tires checked out by a trained technician.  Here are things they’ll check:

• Tread.  Tread is the part of the tire that touches the road surface.  Different tires have different tread patterns and something called tread blocks - the raised rubber parts that contact the road. The longer a tire has been on a vehicle, the more of that rubber wears off.  The technician will check to see if there’s enough of that tread left on your tire for sufficient traction to accelerate, steer, and brake.
• Pressure. It’s important your tires be inflated properly so your tires will perform the way they’re designed while driving.  If your tires have low air pressure, the technician will check to see why, perhaps cracks in the sidewall from age, a nail in the rubber picked up on the road, or bulges. It’s also important your tires are not overinflated too.
• Wear.  Your tires should wear evenly.  If they haven’t, the uneven wear can cause vibrations that you can feel in the steering wheel.  Maybe the whole vehicle shakes at a certain speed.  Your vehicle may require other services such as balancing, alignment, or suspension repairs to prevent future tire damage.
• Age.  Your tires may have adequate tread, but if they’re too old, it’s time for new. Rubber gets old, and when it does, it loses its elasticity.  Ever find an old rubber band and tried to stretch it? It’s brittle and will break easily. Hotter climates will age rubber—and tires—faster. All tires have their date of manufacture stamped on them, so your service adviser will be able to see when your tires were made.

If it’s time to replace your tires, you’ll find you have many choices for new ones: different brands, models, designs, etc.  Your service adviser can help you figure out which ones are right for you. It’s much better—and safer—to do it before one of them fails at the least opportune time.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

If you keep up on technology trends, then you may be intrigued about synthetic motor oil.  It was introduced in the 1960s when Mobil came up with it.  Mobil's oil was different from conventional motor oil because it was first broken down to its basic molecules.  Then, Mobil removed additional impurities from crude oil and "tailored them to the demands of modern engines."

Synthetic oil is becoming more popular now because of its advantages over conventional oil. It's more resistant to sludge forming in an engine.  It is more efficient and protects engines better under temperature extremes.  Because it allows drivers to go longer between oil changes, many feel it's more convenient. 

The downside is that synthetic oil is more expensive, but because it doesn't need changing as often, the cost can be pretty comparable in the long run.

Those who drive high performance vehicles (think Audi, BMW, Mercedes) are already using synthetic oil if they're following their manufacturer's guidelines.  Other manufacturers recommend a synthetic blend.  So for those who are using conventional oil, you may want to consult your service advisor for some recommendations if you want to switch to synthetic. 

If you're the type who always waits until the last-minute or doesn't ever get in quite in time for the recommended oil change interval, the longer gap required between changes with synthetic oil may appeal to you.  In some cases, you can go up to 15,000 miles/24,000 km between changes. 

If you drive in a very cold climate, synthetic oil can flow more easily at startup and may offer quicker engine protection.  On the other hand, in hot climates, synthetic oil can resist heat breakdown better.

Or you may be one of those drivers who have been getting along fine with conventional oil changes.  Millions do.  Just remember that changing your oil is considered the most important maintenance you can do on your vehicle, so make sure it's done at the right time and with the oil that best suits your driving needs.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

You know your body temperature is supposed to be 98.6 degrees F, 37 degrees C.  Your vehicle has a normal temperature, too, and if you pay attention to it, that can save you some big headaches down the road.

Many vehicles have a temperature gauge on the dash that takes the temperature of the engine's coolant.  Some have a thermometer symbol, some read C-H (cold to hot). Many will have a red zone that shows when water temperature is getting into the danger zone.  Others are digital and have a red warning light that signals overheating.  And some vehicles have a light that goes on when the engine temperature is out of the normal range.

If your vehicle has a gauge, pay attention to it.  If you need help locating it, ask one of our Camarillo Car Care Center experts to give you a quick explanation.  Chances are when the vehicle has been running for 15 minutes or more, the temperature gauge will settle into its own "normal" zone, often just below the midway point.  If you have a digital readout, remember what that "normal" temperature is.  Here's why.

At any point when you're driving, the temperature gauge is the quickest way to get a sense that the engine is running the way it should, a quick health checkup, as it were. Say you're on a 3-hour trip, glance at that gauge every hour or so.  It should always be in the same spot.  If it starts to move one way or the other, you may be able to catch a problem before it gets serious.

Pay special attention to it moving into the hot zone.  The needle on the gauge is the easiest and least distracting way to see an engine heating up, but on a digital gauge, start paying attention if the temperature reaches 240ºF/115ºC or more.

Remember, though, that just because the gauge reads "hot" doesn't mean your engine is on the verge of burning up.  It could be a bad sensor and the engine will be at a normal temperature.  But it also could be a failing water pump, coolant leak or thermostat.  By pulling off the road and observing your engine, it will give you a pretty good idea if it's running hot or not.

If the gauge is too "cold," it could be a broken gauge or thermostat sticking open.  Usually being in the cold range isn't as worrisome, but you should have it checked out since other systems may be affected.

Heat is one of a vehicle's worst enemies, especially when it comes from within.  Know your vehicle's normal temperature and keep an eye on it.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

If you were to name the most important safety feature on your vehicle right now, what would your answer be? A lot of driving experts would agree that it’s your brakes.  Most newer vehicles use a well-engineered and efficient style of brakes called disc brakes. 

The name disc brakes comes from one of the components: a disc attached to the wheel hub that is squeezed by parts called calipers.  If you’ve ever ridden a bicycle with hand brakes, you probably have seen how they squeeze against the rim of the bike wheel to stop the bike. It’s similar to the way your vehicle’s calipers squeeze against the disc rotor, with added parts called brake pads attached to the calipers that are what create the friction and stop your vehicle.

Here’s why disc brakes need regular maintenance.  Over time, that friction creates wear and tear on the brake pads and the rotors, and you’ll start to see the signs.  Your brakes may have one of the 3 “S” sounds: squeaking, squealing, or scraping. The sound is usually the first sign of brake pad wear which can lead to rotor damage.  Soon you may notice a pulsating or vibration when you brake. That’s because your once smooth and straight rotor disc is warping from the heat generated from friction. Or it may be due to wear.  Eventually, your brakes will take a longer distance to stop your vehicle, and the rotors can have grooves carved into them.

When you start noticing any of these signs, it’s a good idea to have them inspected by a trained technician.  They will measure the rotor thickness, check wear patterns for grooves and heat discoloration, and see how much of the brake pads remain. They will also check to make sure all brake components are moving freely, check your brake fluid, and look for corrosion.

Most vehicle manufacturers require worn or damaged rotors to be replaced, not resurfaced. It’s all part of a complete brake job, replacing pads and the brake hardware parts along with the rotors. It reduces the chance of premature failure.

How often you will need your brakes serviced depends on the manufacturer’s recommendations, your driving habits, and the environment you live in.  Your service facility can recommend the best replacement parts based on those factors. 

Regular maintenance and attention are vital for keeping your brakes performing like they are designed to. Remember, your brakes are your vehicle’s most important safety feature.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

It's pretty frustrating when your driver's window won't work.  You can't get your food at the drive-thru without opening the door, have a tough time using the ATM from your vehicle, can't have that fresh breeze blowing through your hair as you listen to your favorite road tunes.

Plus, there's a safety factor.  Your windows provide an escape route in case you need to get out and the doors won't work.  Let's take a look at what's going on when your window won't operate.

Most vehicles these days have power windows.  They have an electric motor in each power window and sometimes those fail.  They often give you a warning that they're on their last legs by making a noise or hesitating, so if you get a sign like that, have a technician check it out. Loss of power can also be due to a blown fuse, a bad switch or faulty wiring.

All windows have something called a regulator that moves the glass up and down.  They have a lot of moving parts in them which can break, become bent, rust or get out of alignment. The glass moves along a window track guide.  Sometimes if the glass gets out of the track, it won't move up and down the way it's designed to do.

When you take your vehicle over to a repair facility, a technician can pinpoint the cause of your malfunctioning window.  Often it involves having to remove the door panel to gain access to the components inside.  But when everything's working right, you'll be able to throw that annoying inconvenience right out the window.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

Most drivers love how easy it is to turn their vehicles, and they have power steering to thank.  Engineers have figured out a way to take some of your engine's power to help you turn. Without it, steering can be quite a chore.  New power systems are electric, but there are still plenty of the older hydraulic power steering systems out there, and it's wise to keep them working the way they should so you don't find yourself stranded without power steering.

Those hydraulic power systems use a fluid under pressure that is pumped to a device that helps you turn your wheels more easily.  It's that pressure that presents the challenge.  After your vehicle's seen a few years on the road, you may find your steering isn't quite as easy as it was.  You may hear a groaning or humming sound when you turn. 

One component that can fail is the pressure hose that carries that fluid from the power steering pump to that turning assist mechanism.  The hose is made of rubber and can leak, crack, get damaged by heat and debris or just get too old.  If yours is ten years old or older, it's likely getting close to the end of its life.

If you think you can just wait until it fails completely, think of these possible consequences.  If the hose or a coupling fails, power steering fluid can blow all over the hot engine.  That fluid is flammable and can start a fire.  Or if you've been driving for a few weeks with low power steering fluid, that could ruin your power steering pump. Replacing the pump is an extra expense you can probably  live without.

A technician will replace the necessary parts and make sure air and contaminants are bled or flushed from the system.  Then, he or she will check for leaks.  Just think how important a properly working power steering system is for safe operation of your vehicle.  Make sure you keep yours in top shape for your safety's sake and the safety of others on the road around you.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

Sometimes the movie is better than the book, sometimes it's the other way around.  But when it comes to your vehicle, the best book of all is the owner's manual. The plot is simple: Owner wants long life and dependable performance from the vehicle, manual has the way to achieve that long life and dependable performance.

And yet, it's amazing that some people will own a vehicle for years and never even crack this book.  They'll only read it when they absolutely have to, for things like finding out how to change the clock. 

Ok, so you're probably not going to rush right over to your glove box and start reading the owner's manual cover to cover.  We know that.  But just think of what you can get out of it.

Consider this.  Those who wrote or helped write this book include the engineers who designed it and the people who tested and refined it.  They know more about your vehicle than anyone, period.  They know how long a part is likely to last and what you need to do to take care of it. They know how far a distance or how long a time you can drive before you have to change certain fluids in it.  They know what temperature it can reach before things will start to break.

And they've put your vehicle model through torture, testing it in the absolute worst conditions to see how to make it stand up to more abuse than it will ever receive.  They've then torn it down, examined it and, in many cases, redesigned the parts to make them even better. 

And they've put down—in fairly minute detail—this blueprint that, if you and our experts at Camarillo Car Care Center follow their suggestions, will make it very likely that your vehicle will serve you well for a long time.  If you don't follow those suggestions, all bets are off.

We didn't even mention that the owner's manual tells you how to operate everything in your car.  How to adjust the heat and air conditioning, how to pair your smartphone with the audio system, how to program your key fob so it won't sound the horn when you lock your vehicle.

Have you lost your manual or did you buy a vehicle that didn't come with one?  Many are available either online or in paper form. If you don't know where to begin with such a long book, try a couple of pages a week, just three minutes.  You’ll discover your vehicle does things you never even knew it could do.  And the movie will never be as good.

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

If you’ve noticed your vehicle is hard to start, stalling, or has lost power, the culprit may be a part with an odd name: the MAF sensor.  You may have never even heard of a MAF sensor, but it’s important that it be working correctly, or you may be experiencing some fairly significant engine issues.

All vehicles bring in air and direct it through an air filter before it goes into your engine, where it mixes with fuel to provide power to get you going. There’s a tube-like device with a sensor inside it that measures how much of that mass of air is passing through. That’s why it’s called a mass air flow sensor, or MAF sensor.  If the MAF sensor isn’t working right, the engine’s computer can’t figure out the right amount of fuel to mix with it, and your engine may hesitate or stall.  Sometimes this will cause your Check Engine Light to come on, and any time it does that, make sure you have your vehicle checked by a professional, so you’ll know what’s going on.

When you take your vehicle into your service facility, a technician will thoroughly check the system to see just where the problems are.  If your air filter is dirty, your MAF sensor may get dirty too, which might be causing the problems.  You may find your fuel economy isn’t what it used to be either.

There are other things that can cause the same symptoms, too, such as a leak in a vacuum hose. It’s also possible that the electrical connector between the MAF sensor and the engine has broken. 

The technician can use electronic diagnostic equipment to help pinpoint the exact problem or problems, replace worn parts, and test drive your vehicle to make sure it’s working correctly.

It’s also a good idea to make sure your air filter is changed regularly. A dirty air filter can contribute to a MAF sensor failure. One of the big benefits of having your vehicle regularly maintained at one facility, is they know your vehicle. So, they keep track of which of your vehicle’s parts should be periodically replaced before problems develop. 

If you keep clean air heading into your engine, it can help your engine work efficiently, and with the power it was engineered to deliver. Isn’t that a breath of fresh air?

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com

Bet you didn't know:

Some of the earliest rearview mirrors were marketed as "Cop Spotters" so drivers would know when police were following them. Who wants a ticket, anyway? According to eBay Motors, Elmer Berger first patented a rearview mirror that was mounted on the front fenders, on the spare tire secured to the side of the car of at the top of the driver's door frame. 

About 80 percent of your vehicle is recyclable. So says The Balance. That means four-fifths of most vehicles can be recycled.  Much of that recycling is done by automotive aftermarket recyclers.  Between the U.S and Canada, they reclaim enough steel to produce 13 million new vehicles.

The man who invented the first modern cruise control couldn't even drive a car because he was blind! His name, says Smithsonian.com, was Ralph Teetor.  Blinded at a young age by a knife accident, Teetor was inspired to create a speed control by a couple of things.  One, the U.S. imposed a mandatory 35 mph/55 kph during World War II to conserve fuel and tire rubber, and Teetor wanted drivers to go a safe and steady speed.  Plus, a chauffeur who drove him around used to randomly slow down and speed up which irritated Teetor.  So he invented a speed control to encourage drivers to drive at a more constant and safer speed.

The first grooved tires were invented in 1904 by Continental.  But that was a big improvement over the very first "tires" which were actually metal hoops that made riding in the first cars a pretty rough experience.  The first rubber tires were solid rubber, not inflatable like today's tires.  Things have come a long way.  Modern tires are made with sophisticated rubber compounds that can deal with heat and cold.  Plus their tread patterns help drivers get better traction on wet roads when it storms.  Still, it's important to make sure yours have enough tread and are properly inflated for maximum safety and performance.

Quite frankly, there's a lot we don't understand about the vehicles we drive.  They're much more complicated than the old horse and buggy that preceded  them.  Leave your vehicle's maintenance and service to highly trained technicians who DO understand how to maintain, diagnose and repair today's modern, sophisticated vehicles. 

Camarillo Car Care Center
2739 Daily Drive
Camarillo, CA 93010
805-482-2853
www.camarillocarcare.com